-40%

Paint over Rust with Underbody Gloss Black Paint, Gallon, TRC-15, RUST-BITE

$ 46.99

Availability: 505 in stock
  • Condition: New
  • Returns Accepted: Returns Accepted
  • Size: gallon
  • Brand: Speedokote
  • Refund will be given as: Money Back
  • Color: Gloss Black
  • Item must be returned within: 30 Days
  • Manufacturer Color Name: Gloss Black
  • Restocking Fee: 20%
  • Manufacturer Part Number: TRC-15
  • Return shipping will be paid by: Buyer

    Description

    This sale is for one gallon of Paint over Rust with Underbody Gloss Black Paint, TRC-15, RUST-BITE
    TRC-15 Gloss Black
    • Home • Auto Restoration • Industrial • Fleet • Marine •
    TECHNICAL DATA
    SUGGESTED USES:
    Heavy equipment, trucks, snow plows, mower decks, tractors and other
    farm machinery, oil field equipment, boat trailers, buses, military vehicles,
    dumpsters, roll offs, fork lifts, propane tanks, truck bodies, storage tanks,
    structural steel, pipes, iron works, gates, fence posts, chain link, steel truck
    rims, metal roofs, sheds, and concrete floors.
    DESCRIPTION:
    Rust-Bite is a high solids, VOC compliant, single component rust preventive
    and underbody coating specifically formulated to permanently stop
    corrosion without the use of primers or topcoats. Rust-Bite protects many
    surfaces from water, chemicals, salt, and other corrosive contaminants. Rust-
    Bite stops rust when applied to rust that is prepared by using a wire brush or
    hand scraper to remove all loose rust or scale. For optimum adhesion
    sandblast with medium grit. Rust-Bite will dry to a flexible rock hard, nonporous
    finish that will not crack, chip, flake or peel. Rust-Bite cures by
    reacting with atmospheric moisture and its cured film resembles that of a
    powder coating or a baked-on finish with the use of no hardeners or heat.
    Rust-Bite seals and protects many surfaces from road salt, gasoline, diesel
    fuel, oils, battery acids, hydraulic fluids, solvents, chemicals, or corrosives.
    Rust-Bite can be top coated with any industrial or automotive finish.
    PREPARATION
    Remove all dirt, grease or oils, clean surfaces using a Wax & Grease
    Remover or equivalent. For heavy build-up scrape or wire brush excess
    material prior to degreasing. Allow surfaces to dry thoroughly. NOTE: Do
    not apply Rust-Bite if atmospheric temperature is below 50°F.
    RUSTED SURFACES:
    Remove loose rust and scale using a stiff wire brush, by grinding, or hand
    tool cleaning. Remove all loose, peeling or bubbling paint. NOTE: Rust-Bite
    works best when applied directly over rust. NOTE: Do not remove all rust or
    apply any type of Rust Converter before applying Rust-Bite.
    BARE, SMOOTH METAL:
    Sandblasting is recommended but sanding with 36 to 80 grit sand-paper is
    also acceptable. When blasting, provide a medium to coarse profile for
    optimum adhesion. Avoid any media that may leave a smooth surface.
    PAINTED SURFACES:
    Previously painted surfaces should be sanded using a 120 to 180 grit
    sandpaper to remove gloss.
    MIXING & HANDLING:
    Container may be under slight pressure. Stir liquid gently until uniformly
    mixed. Do not shake, shaking will cause Rust-Bite to build pressure in can.
    Never work directly from the Rust-Bite can unless the entire contents will be
    used in a single painting session. Always pour what will be used into a
    separate container.
    NOTE: Never pour unused product back into original
    container after use.
    NOTE: Before closing Rust-Bite container apply a sheet
    of plastic or food wrap over can, Rust-Bite will adhere lid to can if plastic is
    not applied.
    Never allow can to sit opened when not in use. WEAR
    GLOVES DURING USE Skin contact should be avoided. Do not attempt to
    remove dried Chassis Saver from skin with solvent; soak in warm, soapy
    water. Once product has stained skin, only time will remove it.
    APPLICATION & REDUCING:
    Apply 2-4 coats allowing 3 to 8 hours between coats depending on temp
    and humidity. Each coat should be dry to touch with no tackiness before
    applying next coat. Rust-Bite is a moisture cure finish which when applied
    too heavy will have a tendency to bubble while curing. Avoid bubbling by
    applying thin coats only. Higher temps and humidity will shorten drying
    time. Low temp and humidity will lengthen dry. Do not apply Rust-Bite if
    temperature is below 50°F. Never use lacquer thinner as a reducer for Rust-
    Bite or to wipe surfaces prior to painting.
    BRUSH APPLICATION:
    Apply thin, even coats using a nylon brush. For better flow and leveling, add
    up to 10% TRC-01 Reducer.
    SPRAY APPLICATION:
    Reduce up to 10% using TRC-01 Reducer. Apply medium-wet coats while
    maintaining a gun distance of 12 to 14 inches. Spray tip size should be: 1.2 to
    1.4mm.
    NOTE:
    For surfaces that will be
    exposed to UV (sunlight), wait 24 hours, sand and apply a UV resistant single stage urethane paint.
    RECOAT:
    For films cured over 24 hours, sand using 400-grit abrasive to remove
    gloss before recoating.
    Health and Safety:
    See Safety Data Sheet and labels for additional safety information and handling instructions.
    * The contents of this package may have to be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels and SDS’s of all components, since
    the mixture will have the hazards of all its parts.
    * Improper handling and use, for example, poor spray technique, inadequate engineering controls and or lack of Personal Protective Equipment (PPE), may result in hazardous conditions or injury.
    * Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.
    * Provide adequate ventilation for health and fire hazard control.
    * Follow company, product SDS and respirator manufacturer’s recommendations for selection and proper use of respiratory protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory
    requirements.
    * Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on SDS.
    * Always observe all applicable precautions and follow good safety and hygiene practices.
    * Safety Data Sheets are available on website.